It is easy to use, intuitive and safe even in case of an error. An exceptional advantage is that it allows self-locking abseiling and can be used in three different belay modes, depending on the terrain.
Parameters, certifications and legislation
- For use with twin or half dynamic ropes with a diameter of 7.3–9.0 mm.
- For use with a single dynamic rope with a diameter of 8.6–10.5 mm.
- Weight of the belay device alone: 175 g.
- Hot-forged light alloy belay device body.
- PATENTED.
- Supplied (and must be used) together with the specific TONDO SGL HC HMS carabiner.
- Meets EN 15151-2:2012 type 2
- UIAA
- Quality control 100%
- Made in Italy
Individual belay modes
Belaying a leader in ALPINE UP mode (semi-automatic belay device = manual assisted braking):
- Works on the principle of the CLICK UP semi-automatic belay device , but can be used with a single rope as well as twin or half ropes. It works without the need to operate any lever or moving parts and allows arresting a fall simply by holding the free end/ends of the rope in your hand.
- Suitable for belaying a leader on multi-pitch sport routes equipped with bolts.
- Suitable for belaying directly from the belay loop of the harness, or directly from the anchor.
- Allows the belayer to easily lower their partner to the ground – you just need to apply slight pressure from the top of the belay device while keeping the free end of the rope under control.
- Safe even if the ropes are inserted incorrectly! In this case, ALPINE UP does not function as a semi-automatic belay device, but as a standard tubular belay device, thanks to the V-shaped grooves for increased braking effect.
- In this mode, it works as a self-locking abseil device. To abseil, you need to release the plastic lever and push on it with your palm so the locked rope can slide through. With your other hand, you can then control the abseil speed just like with other types of abseil devices. If you let go of the rope, ALPINE UP automatically locks and you remain suspended. This solution replaces the backup Prusiks required when abseiling on a different belay device.
Belaying a leader in dynamic mode (manual belay device = braking the rope slip by hand):
- Works on the principle of a standard tubular device, suitable for dynamically arresting a fall.
- After a leader's fall, the belay device does not lock up and the belayer can soften the impact of the arrested fall by letting the rope slip.
- Suitable for belaying a leader on traditional multi-pitch routes when using cams, pitons and nuts for protection, and when automatic fall blocking is not suitable.
- Braking the rope slip during a fall is ensured by rope friction in the “V” shaped grooves, just like with a standard tubular device.
- Allows lowering a leader or abseiling just like with a standard tubular device.
Belaying a second in GUIDE mode (self-locking mode):
- Independent and self-locking belaying of one or two seconds.
- Possibility of gradually releasing the rope/lowering a second even under load, by placing an additional carabiner in the designated hole and lifting the bottom side of the belay device.
Use exclusively with the TONDO SGL HC HMS carabiner
ALPINE UP is supplied and must be used together with the specific TONDO SGL HC HMS carabiner with wear-resistant anodising and an ACL system (a steel spring preventing the carabiner from twisting), which prevents the carabiner from rotating and potentially cross-loading its minor axis.
Carabiner features:
- Spacious enough for attaching the belay device.
- Hot-forged for maximum strength and durability.
- Shaped profile for the best possible carabiner weight-to-strength ratio.
- Fully oval profile in the areas where the carabiner comes into contact with the rope, for better longevity.
- The carabiner nose does not have a notch, so it does not catch when clipping and unclipping.
- ACL system - a steel spring allowing the carabiner to be attached to the harness belay loop, which fixes its position and prevents cross-loading of the carabiner.
Carabiner parameters:
- Major axis strength: 24 kN
- Open gate strength: 7 kN
- Weight: 75 g
- Gate clearance: 22 mm
- ACL
Carabiner certification and legislation:
- EN 12275:2013-H
- EN 362:2004-A/T
- CE 0333
- UIAA
- Individually tested 100%
- Made in Italy